🚘 BlackVue Dashcam Installation Guide #
⚠️ Before You Begin #
Choose installation locations carefully:
Front camera: Behind the rearview mirror.
Rear camera: At the top center of the rear windshield.
Clean the windshield: Remove any dust, oil, or moisture before sticking the cameras.
Peel off the protective film from both front and rear cameras to prevent overheating.
Do not install the cameras where they might block the driver’s view.
*Note for ELITE 9-1CH users: The rear camera is optional.
📌 Step-by-Step Installation #
Step1. Insert the microSD Card #
Turn off the vehicle engine.
Open the microSD card slot cover on the front camera.
Gently insert the card until it clicks into place and close the cover.
Step2. Mount the Front Camera #
Remove the double-sided tape.
Attach the front camera to the windshield, behind the rearview mirror.
Adjust the lens angle by rotating the camera body.
💡Tips: Tilt the lens slightly downward (~10°) for a 6:4 road-to-sky ratio.
Step3. Mount the Rear Camera (if applicable) #
Peel off the tape film and stick the rear camera to the rear windshield.
Rotate the camera body to adjust the viewing angle.
Step4. Connect the Front and Rear Cameras #
Use the provided rear camera cable:
Plug one end into the ‘Rear’ port of the front camera.
Plug the other into the ‘V out’ port of the rear camera.
Step5. Hide the Rear Camera Cable #
Use the pry tool to gently lift window moldings or rubber seals.
Tuck the cable neatly along the edges for a clean look.
A): Rear camera cable
🔌 Powering Your Dashcam #
You can power your BlackVue dashcam in three main ways. Choose the option that matches your vehicle’s compatibility.
Option A. Using the USB-C PD 3.0 Power Cable #
Use this method if your vehicle has a Type-C port that supports PD 3.0 (Power Delivery 3.0).
Locate the Type-C Port in Your Vehicle
Usually located near the passenger seat (varies by vehicle).
Look for a lightning bolt symbol to confirm PD 3.0 support.
Connect the Cable to the Dashcam
Plug the USB-C PD 3.0 Power Cable into the vehicle’s Type-C port, and the other end into the front camera’s DC-in port.
Hide the Cable
Use the pry tool to lift rubber seals and tuck in the cable neatly along window trim.
A) Rear camera cable / B) USB-C PD 3.0 Power Cable
Start the Engine
The dashcam will automatically power on and start recording.
⚠️Caution
Parking Mode is not supported with USB-C power.
For full features, use a hardwiring kit or battery pack.
Option B. Using the Dual USB-C Car Charger (Type-C Adapter) #
Use this method if:
Your vehicle doesn’t have a Type-C port, or
The Type-C port doesn’t support PD 3.0.
Plug the Dual USB-C Car Charger into the 12V Outlet
Insert the Dual USB-C car charger into your vehicle’s cigarette lighter socket.
Connect the USB-C power cable to the USB-C port labeled “Dashcam” on the adapter.
Connect the USB-C PD 3.0 Power Cable
Connect the cable from the adapter to the front camera’s DC-in port.
Hide the Cable
Use the pry tool to lift rubber seals and tuck in the cable neatly along window trim.
A) Rear camera cable / B) USB-C PD 3.0 Power Cable
Start the Engine
The camera will power on and begin recording automatically.
⚠️Caution
This method also does not support Parking Mode.
To record in parking mode while the engine is off, please connect the Hardwiring Power Cable (Sold separately) or install a Power Magic Battery Pack (sold separately).
Option C: Using the Hardwiring Power Cable #
Locate your vehicle’s fuse box (check your car manual if unsure).
Remove the fuse box cover and identify:
A fuse that powers on with the engine (e.g. audio, cigarette lighter) – connect ACC+ here.
A fuse that’s always powered (e.g. hazard lights, dome light) – connect BATT+ here.
💡Tips: For parking mode and battery protection, connect BATT+ to the hazard light fuse.
Connect the GND (ground) wire to a metal bolt on the vehicle frame.
Plug the power cable into the front camera’s DC in port. The dashcam will power on and start recording.
Option D: Using the Battery (B-130A)
This installation method involves using a dedicated external battery, the Power Magic Ultra Battery (B-130A), to power the dashcam. It is an effective option that provides stable power to the dashcam without burdening the vehicle’s main battery.
✅ Recommended For #
Users who need extended dashcam recording while parked
Users who want to prevent battery discharge of the vehicle
Users looking for a more reliable power source
🔧 Installation Overview #
The B-130A can be charged via the vehicle’s cigarette lighter socket or fuse box, and once fully charged, it supplies power independently to the dashcam.
📘 For detailed installation steps and precautions, please visit the following link:
https://manual.blackvue.com/docs/power-magic-ultra-battery-b-130a/installation/installation-b-130a/
💡Tips
The first time the dashcam runs, firmware is automatically saved to the microSD card. Customize settings after that.
5. Playing and Managing Videos #
📱 Using the BlackVue App #
🔐 Register BlackVue Account #
Download the App
Search for “BlackVue” on the Google Play Store or Apple App Store and install the app on your smartphone.Create an Account
Open the app. On the welcome screen, choose a sign-up method:
Continue with Apple
Continue with Google
Continue with Email
If you choose Continue with Email:
① Enter your email address
Type in your email address and tap Next.
② Create a Password
Set a secure password for your account and tap Next.
③ Agree to Terms
Accept the Terms of Service and Privacy Policy
Confirm that you are 14 years of age or older
(Optional) Subscribe to product news and updates
Tap Next to continue.
④ Verify your Email
A 6-digit confirmation code will be sent to your email.
Enter the code and tap Confirm to complete your registration.
