Click on the Settings button to open the BlackVue settings panel. You will be able to change most of the BlackVue settings to customize its operation.
Select your preferred language for the BlackVue Viewer interface from the dropdown list.
Change the speed unit displayed on the map.
Change the mapping service used.
On some computers videos may not play smoothly in PIP view. If you encounter issues please disable PIP playback.
Select your preferred language for the firmware from the FW language dropdown list. The audio announcements by the dashcam will be in the selected language.
Please backup necessary recordings before changing time or image quality settings. If any of the aforementioned settings are changed and saved, the dashcam will format the microSD card and delete all recordings stored on the card including locked event files in order to ensure optimal performance.
Select your time zone to auto-sync with GPS time or you can set the time and date manually after enabling Manual time setting.
• The factory setting is GMT -11.
Some examples of GMT time offsets are:
– GMT-7: Los Angeles
– GMT-4: New York
– GMT+0: London
– GMT+1: Paris
– GMT+3: Moscow
– GMT+8: Singapore
– GMT+9: Seoul
– GMT+10: Sydney
If you are unsure of your GMT offset please look up your city on https://greenwichmeantime.com/
*Selecting Daylight saving time will advance the clock by one hour
• When setting the time manually, please set to the expected time you will use the BlackVue (not the present time).
Resolution and frame rate is fixed at “[email protected] + [email protected]”. This the rear camera records Full HD video at 30 frames per second.
• The playback of 60 fps videos depends on your computer’s hardware and software. Older computers may not support 60 fps video playback. If you encounter issues please check your computer’s video playback capabilities.
• Frame rate may vary during Wi-Fi streaming.
You can adjust the recording image quality (bit rate) settings. Choose between:
• Highest (Extreme) (Front: 25 Mbit/s, Rear: 10 Mbit/s)
• Highest (Front: 12 Mbit/s, Rear: 10 Mbit/s)
• High (Front: 10 Mbit/s, Rear: 8 Mbit/s)
• Normal (Front: 8 Mbit/s, Rear: 6 Mbit/s)
Increasing the image quality will increase the size of the video files. Loading and copying time will increase accordingly.
The dashcam has an intrinsic night vision feature. If you want to enhance it, enable Enhanced night vision – you can choose to have it turned on all the time, or have it active only in parking mode.
You can adjust the recording brightness level of the front camera.
You can adjust the recording brightness level of the rear camera.
When turned off the dashcam does not record in normal mode.
If enabled, the dashcam switches from normal mode to parking mode when the vehicle is turned off (ACC+) or stationary for 5 minutes (G-Sensor). There are two parking mode options. Choose “Motion & Impact detection” to save a parking recording when motion is detected in the dashcam’s field of view. If the G-sensor detects an impact/bump the dashcam saves a separate event recording file.
Alternatively, if you choose “Time lapse” the camera continuously records 1 frame per second and saves recordings that playback at 30 times normal speed. If the G-sensor detects an impact/bump the camera saves a separate event recording file at normal speed.
When turned on, the front and rear camera record together.
When turned off, the rear camera stops recording 5 minutes after entering parking mode. Rear camera recording restarts when entering normal mode.
When turned off the dashcam does not record audio.
Turn on/off the date and time display on videos.
Select km/h, MPH, or turn off.
Video segment length is fixed at 1 minute.
Turning on this option will lock the following recording types and stop them from being overwritten by newer recordings:
– Impact event recordings during normal and parking mode (E); and
– Manual recordings (M).
A maximum of 50 files can be locked. Once this limit is reached, to lock new recordings please review locked files on the microSD card and free up space, or enable ‘Overwrite locked event files when full’ to allow the oldest locked files to be overwritten.
If you installed the front camera in a flipped position, use this setting to rotate the front camera image 180°.
Use this setting to rotate the rear camera image 180° or mirror the video.
The G-sensor measures the movement of your vehicle through 3 axes – up and down, side to side, and front and back. When the G-sensor detects significant or sudden movement (such as an impact or collision) it will trigger an event recording. You can adjust the sensitivity so minor incidents and bumps don’t trigger an event recording. To turn off event recordings by impact detection set the G-sensor sensitivity to off.
In parking mode the dashcam continuously buffers video and saves a parking recording when motion is detected in the dashcam’s field of view.
You can adjust the sensitivity of the motion detection so minor motion caused by wind or rain doesn’t trigger a recording. Please take into account your vehicle’s surroundings when adjusting the sensitivity.
Advanced sensitivity settings allows you to fine-tune the event recording G-Sensor threshold, while watching pre-recorded G-Sensor data and video as a reference.
1. Click the Advanced settings button.
2. Double click the video from the list that you want to use as a G-Sensor data reference.
3. Set the thresholds by adjusting the control bars next to each G-Sensor axis. Any G-Sensor data that crosses over the threshold on any of the 3 axes will trigger an Event recording.
4. Click Save and close.
You can manually choose the detection regions to reduce the risk of triggering unwanted motion recordings due to trees swaying in the wind, far-away moving objects, etc. By default, all the regions are selected. If you want to ignore motion detection in particular region(s), unselect them.
You can turn the recording status LED on/off.
You can turn the front security LED on/off for normal mode.
You can turn the front security LED on/off for parking mode.
You can turn the rear security LED on/off.
You can turn the LTE LED on/off for parking mode.
You can turn the Wi-Fi LED on/off for parking mode.
You can choose the function of the proximity sensor. Available options are:
– Turn on/off audio recording (default)
– Manual recording trigger
The sensor can also be disabled completely.
You can adjust the voice guidance (announcements) you want to hear.
• Impact detected in parking mode voice alert notifies when exiting parking mode if an impact had been detected during parking mode, however, it ignores any impact detected within three minutes before exiting parking mode.
You can adjust the volume of the voice guidance (announcements).
The dashcam reboots automatically once-a-day if in parking mode at the set time for improved stability. If the dashcam is recording at the set time, the scheduled reboot is skipped. You can enable/disable and change the time for scheduled rebooting. Default time is 03:00 am.
Set a speed limit (up to 300 km/h or 200 MPH) for the speed alert. When the vehicle exceeds the specified speed limit, the dashcam beeps and switches to event recording. After saving one event recording file the dashcam switches back to normal mode recording.
When the battery protection is on, power is supplied to your BlackVue while the vehicle is off (ACC+ off) and also prevents the vehicle from battery discharge while it is parked. BlackVue will automatically power down according to the set cut-off timer and voltage.
• Recommended settings for low voltage cut-off is 12V or higher during winter. – If battery protection is off, BlackVue will not operate when the vehicle is turned off (ACC+ off).
You can create a user text overlay of up to 20 characters using a combination of English letters (A – Z, a – z), numbers (0 – 9), and symbols (:;‘/+-_()$#). The text is overlaid in the top-left corner of the recorded videos.
You can change the dashcam’s SSID and Wi-Fi login password.
Wi-Fi will automatically switch on when you turn on the dashcam and remain on. You can adjust the settings for Wi-Fi to automatically turn off.
• Wi-Fi auto turn off setting does not affect Wi-Fi hotspot for Cloud connectivity.
If you don’t use the Cloud service you can turn it off.
Up to 3 Wi-Fi hotspot SSIDs can be saved (e.g. home, portable hotspot and work). Choose your Wi-Fi hotspot from the list and enter the password. Tap 2 and 3 to add settings for additional hotspots.
Your BlackVue will try to connect to hotspot 1 first. If it cannot connect to hotspot 1, it will then try to connect to hotspot 2, and then hotspot 3.
• The DR750X-2CH dashcam is not compatible with 5GHz wireless networks.
You can customize when you want to receive push notifications.
You can automatically apply the configuration by inserting the microSD card into the BlackVue dashcam and turning it on. Configure the settings before using the dashcam. To reset all settings to their defaults press the Reset button at the bottom of the settings panel.
Powered by BetterDocs